Tyan B2935G28V4H Especificações

Transport GT28B2935Service Engineer’s Manual

2 Chapter 1: Overview1.2 FeaturesEnclosure• Industry 19” rack-mountable 1U chassis• Dimension:D 29.2 x W 17.2 x H 1.72 inch (741.6x436x43.6mm)• Two no

Chapter 1: Overview 3Server Cooling• (6) 40*40*56mm 15000rpm heavy-duty fans with fan speed monitor/control• (2) 40*40*28mm 15000rpm heavy-duty fans w

4 Chapter 1: Overview1.3 Unpacking This section describes the GT28 (B2935) package contents and accessories. Open the box carefully and ensure that al

Chapter 1: Overview 51.3.2 AccessoriesIf any items are missing or appear damaged, contact your retailer or browse to TYAN’s Web site for service: http

6 Chapter 1: OverviewRail KitMounting Brackets x 4Screws KitFrontRearSliding BracketsFront L-Bracket x 2Rear L-Bracket x 2Sliding Rails x 2

Chapter 1: Overview 71.4 About the ProductThis section contains the hardware diagrams and a block diagram of the GT28 system.1.4.1 System Front View1.

8 Chapter 1: Overview1.4.3 LED DefinitionFront PanelRear I/O LED *Right or Left is viewed from the rear.LED Color S

Chapter 1: Overview 91.4.4 System Internal View1. EPS 12V Power Supply2. PCI-E x 8 Slot (with riser card)3. Memory Slots4. Power Board (M1028)5. CPU S

10 Chapter 1: Overview1.4.5 GT28 (B2935) System Block Diagram(B2935G28V4HI)

Chapter 1: Overview 111.4.6 S2935 Board Parts, Jumpers, and Connectors

12 Chapter 1: OverviewJumpers and ConnectorsJumper/ConnectorFunctionJ7 ID LED HeaderJ8 IB LED HeaderJ9 IPMB Pin HeaderJ22 LCM Pin HeaderJ24 Barebone F

Chapter 1: Overview 13J24 Barebone Front Panel Pin HeaderPower SupplyPower connector: 12-pin (PW1/PW4)Power connector: 8-pin (PW2/PW3)Pin Signal Pin S

14 Chapter 1: Overview

Chapter 2: Setting Up 15Chapter 2: Setting Up2.0.1 Before You BeginThis chapter explains how to install the CPU, CPU heatsink, memory modules, and har

16 Chapter 2: Setting Up2.0.4 PrecautionsComponents and electronic circuit boards can be damaged by discharges of static electricity. Working on a sys

Chapter 2: Setting Up 172.1 Rack MountingAfter installing the necessary components, the Transport GT28 can be mounted in a rack using the supplied rac

18 Chapter 2: Setting UpInstalling the Inner Rails to Chassis1. Screw the mounting ear to each side of Transport GT28 as shown using 2 screws from the

Chapter 2: Setting Up 194. Locate the front and rear brackets.5. Reserve 40mm on the front bracket. Secure the front bracket to outer rail with 2 M4-4

20 Chapter 2: Setting Up7. Secure the outer rail to the rack using 2 brackets and 4 M5-8L(B) screws for each side. Secure the mounting brackets from i

Chapter 2: Setting Up 2110. Press the latch (A) to push the whole system into the rack (B).11. Secure the mounting ears of chassis to the rack with 2

iPREFACECopyrightThis publication, including all photographs, illustrations, and software, is protected under international copyright laws, with all

22 Chapter 2: Setting Up2.2 Installing Motherboard ComponentsThis section describes how to install components on to the moth-erboard, including CPU, m

Chapter 2: Setting Up 232.2.2 Installing the CPU and HeatsinkFollow these instructions to install the CPU and CPU heatsink.1. Lift up the air ducts as

24 Chapter 2: Setting Up4. Pull the CPU lever up to unlock the CPU socket.5. Open the socket in the direction as shown.6. Place the CPU in the CPU soc

Chapter 2: Setting Up 257. Close the socket in the direction as shown.8. Press the CPU socket lever down to secure the CPU.9. Place the heatsink on to

26 Chapter 2: Setting Up2.2.3 Installing the MemoryFollow these instructions to install the memory modules on the motherboard.Key points to note befor

Chapter 2: Setting Up 273. Align the memory module with the slot. The module has indentations that align with notches in the slots.4. Insert the memor

28 Chapter 2: Setting UpAttention When Installing the Memory!For optimal dual channel DDRII operation, always install memory in pairs beginning with D

Chapter 2: Setting Up 292.2.4 Installing a PCI-E Low Profile CardThe TYAN Transport GT28 (B2935) has two PCI-E Low Profile card slots with pre-install

30 Chapter 2: Setting Up3. Move the I/O shield to left as shown and then take off the I/O shield.4. Locate the PCI-E slot on the riser, and insert a P

Chapter 2: Setting Up 312.3 Installing the Hard Drive for GT28 (B2935)The TYAN Transport GT28 barebone system supports SAS/SATA hard drives.Follow the

ii Federal Communications Commission (FCC)Notice for the USA Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15

32 Chapter 2: Setting Up4. Remove the drive tray holder.5. Place a hard drive into the drive tray.6. Use six HDD screws to secure the HDD.

Chapter 2: Setting Up 337. Reinsert the drive tray into the chassis, ensuring that the drive tray is completely inserted into the chassis. 8. Close th

34 Chapter 2: Setting Up

Chapter 3: Replacing Pre-Installed Components 35Chapter 3: Replacing Pre-Installed Components3.1 IntroductionThis chapter explains how to replace pre-

36 Chapter 3: Replacing Pre-Installed Components3.1.3 PrecautionsComponents and electronic circuit boards can be damaged by static electricity. Workin

Chapter 3: Replacing Pre-Installed Components 373.2 Disassembly FlowchartThe following flowchart outlines the disassembly procedure.Rear ComponentsCha

38 Chapter 3: Replacing Pre-Installed Components3.3 Removing the CoverBefore replacing any parts you must remove the chassis cover.Follow these instru

Chapter 3: Replacing Pre-Installed Components 393.4 Replacing Motherboard ComponentsFollow these instructions to replace motherboard components, inclu

40 Chapter 3: Replacing Pre-Installed Components3. Lift up the power board cover as shown.4. Disconnect the power connectors, front panel connector, p

Chapter 3: Replacing Pre-Installed Components 415. Disconnect the SATA connectors and LED cable. Refer to the mainboard layout for the locations.6. Re

iiiAbout this ManualThis manual provides you with instructions on installing your Transport GT28, and consists of the following sections:Chapter 1: P

42 Chapter 3: Replacing Pre-Installed Components3.4.2 Removing the MotherboardAfter removing all the cables from the motherboard, follow these instruc

Chapter 3: Replacing Pre-Installed Components 433.5 Replacing the LED Control BoardFollow these instructions to replace the LED control board.1. Remov

44 Chapter 3: Replacing Pre-Installed Components4. Unplug the USB cable and the ribbon cable from their respec-tive connectors.5. Remove the three scr

Chapter 3: Replacing Pre-Installed Components 456. Lift the LED control board free from the front cover chassis. After replacement, insert the unit to

46 Chapter 3: Replacing Pre-Installed Components3.5.2 M1003 LED Control Board Connector Pin Definition J1 USB Connector

Chapter 3: Replacing Pre-Installed Components 473.6 Replacing the SAS/SATA Backplane1. Remove all the connected cables from the SAS/SATA back-plane.2.

48 Chapter 3: Replacing Pre-Installed Components4. Remove the ten screws that secure the bracket to the SAS/SATA backplane5. Release the SAS/SATA back

Chapter 3: Replacing Pre-Installed Components 493.6.1 SAS/SATA Backplane (M1228) FeaturesU4, SAS/SATA 2U3, SAS/SATA 1U2, SAS/SATA 2U1, SAS/SATA 1(Righ

50 Chapter 3: Replacing Pre-Installed ComponentsPW2 Power ConnectorJ5, SAS/SATA 1J3, SAS/SATA 2J2, SAS/SATA 1J1, SAS/SATA 2PW1 Power ConnectorConnecto

Chapter 3: Replacing Pre-Installed Components 513.7 Replacing the Cooling FansWarning: To avoid danger, keep fingers and other body parts away from th

iv SAFETY INFORMATIONBefore installing and using the Transport GT28, take note of the following precautions:– Read all instructions carefully.– Do

52 Chapter 3: Replacing Pre-Installed Components3. Remove the fan you want to replace in the direction of the arrow from the fan cradle.4. Replace a n

Chapter 3: Replacing Pre-Installed Components 533.8 Replacing the Power SupplyFollow these instructions to replace the power board and power supply in

54 Chapter 3: Replacing Pre-Installed Components3. Remove the four screws securing the power board cover to the chassis as shown.4. Lift up the power

Chapter 3: Replacing Pre-Installed Components 556. Remove the four screws securing the power board to the chassis. Then lift off the power board free

56 Chapter 3: Replacing Pre-Installed Components3.8.2 M1028 Power Board FeaturesJ3/J4 PS_ON&PGD ConnectorJ1/J2 SMBUS Signal Connector1Key PIN2 PS

Chapter 3: Replacing Pre-Installed Components 573.8.3 Replacing the Power Supply1. Press the latch on the power supply front panel to the right as sho

58 Chapter 3: Replacing Pre-Installed Components

59Appendix I: BIOS DifferencesThe BIOS of B2935 is similar to the BIOS of S2935. There is only one menu different. You may refer to the attached moth

60 B2935 Advanced/Hardware Health InformationTable of DifferencesS2935 B2935Auto FAN Control Disabled EnabledHardware Monitor FanFAN1 (TACH1)FAN2 (TA

61Appendix II: Cable Connection TablesNOTE: The Transport GT28 chassis supports two nodes.SAS/SATA CablesFAN CablesTable 1: Transport GT28-B2935M1228

vTable of ContentsChapter 1:Overview1.1 About the TYAN Transport GT28 B2935 . . . . . . . . . . . . . . . . . . .11.2 Features . . . . . . . . . .

62 Power Supply CablesThe Other CablesTable 3: M1028 to Motherboard/ M1228M1028 Connect to Motherboard/ M1228Node 1Fixed power cableÆMotherboardPW3 8

63Appendix III: Installing an SMDC CardThis section provides information on installing optional M3295-2/ M3296 SMDC cards to your motherboard.Follow

64 3.Insert the M3295-2/M3296 SMDC card into the connector as shown.4.When inserted properly, the SO-DIMM connector locking levers lock automatically

65Appendix IV: FRU Parts TableSee TYAN’s website for FRU Parts Table: www.tyan.com

66 Technical SupportIf a problem arises with your system, you should first turn to your dealer for direct support. Your system has most likely been c

673. Contact your dealer for help BEFORE calling TYAN.4. Check the TYAN user group: alt.comp.periphs.main-board.TYANReturning Merchandise for Service

vi 3.5.1M1003 LED Control Board Features . . . . . . . . . . . . . . . . . .453.5.2M1003 LED Control Board Connector Pin Definition . . . . 463.6

Chapter 1: Overview 1Chapter 1: Overview1.1 About the TYAN Transport GT28 B2935Congratulations on your purchase of the TYAN TransportTM GT28 (B2935),